アルミニウム製ブレッドボード、25 mm厚、高剛性
- Aluminum Plates and Core Minimize Thermal Instabilities
- High Strength-to-Weight Ratio
- Non-Magnetic Material
- T-Slot in Sides for Rail Compatibility
PBG1212F
12" x 12" UltraLight™ Optical Breadboard
See BB Selection Guide Tab
T-Slot for 25 mm Rail CompatibilityPlease Wait
General Specificationsa | ||
---|---|---|
Breadboard Thickness | 25 mm (0.98") | |
Top Skin Flatness | ±0.15 mm (±0.006") Over Any 0.3 m2 | |
Construction | Double-Plate, Single-Honeycomb Core, Athermalized Aluminum Design | |
Top Plate | 6 mm Thick Aluminum | |
Bottom Plate | 3 mm Thick Aluminum | |
Core | High-Density Plated Aluminum Honeycomb | |
Finish | Matte Black Paint | |
Maximum Screw Depth | 6 mm (0.24") from Top Surface | |
Breadboard Mounting | 1/4"-20 (M6) Taps on Bottom Plate |
特長
- 厚さ:25 mm
- 側面は25 mmレールが取り付け可能なTスロット付き
- 同じ表面積のアルミニウム製ブレッドボードに比べて軽量
- オールアルミニウムを使用することによりCTEを整合し、熱による影響を低減
- 幅広いサイズ(W x L)をご用意:
- 300 mm x 300 mm~900 mm x 1500 mm
- 厚さ12.7 mmのアルミニウム製ブレッドボードよりも高剛性(詳細は「コンストラクション」タブをご覧ください)。
- 表面は艶消しの黒色なので反射および後方散乱が低減
- 高密度のハニカムコアによる優れた静的および動的剛性
- カスタムサイズもご提供可能です(詳細は当社までお問い合わせください)。
Click to Enlarge
側面に取付可能な25 mmレールにより、光学筐体を簡単に構築・取り付けできます。なお、こちらの用途には筐体のヒンジをブレッドボードに取り付けるためのドロップイン式のTナットと標準的なM4キャップスクリュが必要です。
当社のUltraLight™ハニカムブレッドボードは強度重量比が高く、オールアルミニウムの構造になっています。 この構造により、すべてのブレッドボードは同様の熱拡張係数を持つため、熱的不安定性が最小に抑えられます。これらのブレッドボードは、可搬性と動的剛性が重要な光学系のセットアップに適しています。一般に、完全な非磁性面が必要とされる用途や、アルミニウム、スチールまたは花崗岩製のブレッドボードの代替品として使用されています。また、ブレッドボードは、当社の25 mmレールとアクセサリが取り付け可能なTスロット付きです。Tスロットを使用することにより、タップ穴無しのレールシステムや光学筐体を構築可能です。こちらのブレッドボードの角にはプラスチック製のカバーも付いており、内2つのカバーには型番またはシリアルナンバが記されています。
ブレッドボードの選択
アルミニウム製の光学ブレッドボードを選ぶ際は、剛性が重要な検討要素になります。当社では、高剛性タイプと剛性強化タイプの2種類のアルミニウム製光学ブレッドボードをご用意しております。荷重負荷時のたわみは、よく厚さと関連付けて考えられますが、実際にはボードの剛性がたわみを決定します。
剛性が高くなると、荷重や力が負荷されてもブレッドボードが曲がりにくくなります。したがって、通常の高剛性タイプののブレッドボードの中心部に高荷重を負荷すると、剛性強化タイプのブレッドボードに同じ荷重を負荷した場合に比べてたわみが大きくなります。このたわみにより、ブレッドボードの両端に乗せた2つの部品の間にミスアライメントが生じます。このことは、例えば直線の光軸を保持したまま、光学系のセットアップをブレッドボード上で移動させる必要のある実験を行う場合に特に重要です。
当社では、優れた剛性とダンピング特性を有するNexus®スチールハニカム製ブレッドボードを豊富に取り揃えております。当社の異なる種類のブレッドボードの比較については、「ブレッドボードセレクションガイド」タブをご覧ください。
フレームと除振脚
当社ではブレッドボード用に多数の支柱をご用意しております。当社のブレッドボード用フレームには、除振無し、あるいは パッシブ型やアクティブ型除振付きをご用意しております。ブレッドボードをテーブル上面に取り付ける際に使用するパッシブ型および電子制御の除振装置用脚もご用意しております。
Click to Enlarge
構成の特長
Ultralight™アルミニウム製ハニカムブレッドボードの構成
当社のUltraLight™光学ブレッドボードは強度重量比が高く、優れた熱安定性を有しています。これらのブレッドボードは、可搬性と動的剛性が重要な光学系のセットアップに適しています。型番末尾がFまたはAのブレッドボードの側面には、当社の25 mmレールとアクセサリが取り付け可能なTスロット付きで、末尾にアルファベット文字が付いていないブレッドボードは標準的なアルミニウム製側面パネルとなります。
右図のように、これらのブレッドボードは、2枚のプレートと1枚のハニカムで設計されており、優れた静的および動的剛性を有しています(下記の試験をご参照ください)。最上位の層は6 mmのアルミニウム製天板です。2番目の層は、メインのアルミニウム製ハニカム構造に3 mmのアルミニウム製底板が組み合わされています。メインとなるハニカムコアは、高精度に成形されたアルミニウムの薄板からできていて、高抗張力のエポキシ接着剤で接着されています。このオールアルミニウムの構造により、温度変化による熱湾曲を最小に抑えています。
優れた表面平面度
多くの実験用セットアップにおいて、ブレッドボードの平面度は非常に重要です。局所的な平面度が十分でない場合、ブレッドボード全体の部品の高さを再調整する必要が生じたり、部品の角度偏差が発生したりする場合があります。当社のブレッドボードは、0.3 m2あたり±0.15 mmと優れた平面度を有していますが、これは高い平面度を保持するための製造工程における特別な取扱いによって実現された、高精度なアルミニウム製プレートによるものです。特殊な熱圧着接合プロセスによって製造中には応力が発生しないため、天板の平面度を保持することができます。
剛性比較試験:アルミニウム製ハニカムブレッドボードvs.アルミニウム製ブレッドボード
図 2: このグラフは、ブレッドボードPBG60120AおよびMB60120/Mの中心部に均一な力を負荷した時の変位量を示しています(左の図参照)。
目的: 寸法600 mm x 1200 mm x 25 mm、梱包材を除く重量が20.3 kg のUltraLightブレッドボードPBG60120Aが、同じサイズで厚さ12.7 mm、梱包材を除く重量が23.49 kgのアルミニウム製ブレッドボードMB60120/Mよりも優れた剛性を有していることを示します。
方法: 下の図1のように、各テーブルを1 m離れた支点によって支持しました。次にブレッドボードの中心部に荷重を均一にかけ、たわみを計測しました。取得したデータから、右にあるような力vs.変位量のグラフを作成しました。
図 1: どちらのブレッドボードも2つの支点で支持されています。
均一な力を各ブレッドボードに負荷してたわみを測定しました。
結果: 図 2に示されているように、アルミニウム製ハニカムブレッドボードPBG60120Aは、アルミニウム製ブレッドボードMB60120/Mに比べて19%軽量ですが、強度は4.1倍であることがわかりました。これは2つの剛性値1.44 x 106および3.49 x 105の比から算出しました。
結論: 図2に示すように、UltraLightアルミニウム製ハニカムブレッドボードPBG60120Aは、アルミニウム製ブレッドボードMB60120/Mに比べて3.19 kg軽量ですが、剛性ははるかに優れていることが明らかになりました。したがって、当社のUltraLightシリーズのブレッドボードは、軽量で剛性に優れたブレッドボードを必要とする用途に適しています。
Posted Comments: | |
Alan Yamamoto
 (posted 2022-04-12 19:30:18.763) I wanted to calculate the strength of the threads in the face-sheet, for this I was curious about the alloy and temper of the tapped face=sheet as well as as its thickness. cwright
 (posted 2022-04-13 10:19:29.0) Response from Charles at Thorlabs: Thank you for your query. The top skin is 5251-H22 Aluminium and is 6 mm thick. Andrew Huibers
 (posted 2021-03-01 18:47:56.513) I ordered a PBG1236F.
The top is 1/4-20 but the threads on the back are M6 !
I don't think your drawing is correct. Or there was a manufacturing error.
I am not crazy about this! YLohia
 (posted 2021-04-14 02:36:26.0) Thanks for your feedback regarding your recently purchased PBG1236F. We apologize for any inconvenience this my have caused. We would be happy to offer a replacement breadboard with the correct bottom skin threading. Please note that these holes are really only used for mounting feet which can be supplied in metric. hammons3
 (posted 2018-05-15 16:51:15.457) Hello,
I would like to know if it is possible to safely drill a 1/4 inch hole through the top and bottom of the breadboard. the hole would be through an existing location of a tapped hole that is already there.
thanks,
josh bhallewell
 (posted 2018-05-31 12:10:40.0) Response from Ben at Thorlabs: Thank you for your question. We would advise against drilling through a PBG* breadboard as there is no guarantee of where the Aluminium Core is located with respect to the hole. If you contact the core with your tooling, this could likely cause damage to the breadboard & your tooling. We can supply a new special breadboard with the hole already in place surrounded by a liner. Please contact your local Tech Support team for further details of Custom Breadboard capabilities & pricing. tomasz.giela
 (posted 2018-02-20 15:24:18.357) Is there a possibility to have some through holes made in the breadboard of this kind? I am trying to design simple way to mount the breadboad to custom aluminum frame. I will be glad for help. bwood
 (posted 2018-02-28 06:08:04.0) Response from Ben at Thorlabs: Thank you for your feedback. We have many different custom options for our tables and breadboards, including through holes, available. I will be in contact with you directly to gather more information on your requirements. peter.rossoni-1
 (posted 2016-03-03 17:18:14.31) I'm interested in calculating modal frequencies of our breadboard, in our custom mounting arrangement. How can I get the exact dimensions of the facesheets and honeycomb core specs? user
 (posted 2016-02-09 01:24:12.523) What is the difference in packaged and unpackaged mass? jlow
 (posted 2016-02-15 10:01:19.0) Response from Jeremy at Thorlabs: The unpackaged weight is just the weight of the breadboard. The packaged weight includes both the breadboard and the shipping packaging. songxindong
 (posted 2015-11-30 15:33:17.19) Hi Thorlabs,
I have previously bought a PBG11118 and a PBG11107. I recently want to buy a PBG11111. However, I found out the distances between back mounting holes are not aligned in inch multiples. Is there any possibilities that I can customize a PBG11111 with back holes intervals as 40" and 24", rather than 40.9" and 23.2"? Thank you.
Best,
Xindong besembeson
 (posted 2015-12-03 01:09:55.0) Response from Bweh at Thorlabs USA: Yes this customization is possible. With the current version, you can also use similar 1.5" posts with a base such as the PB4 and clamping fork such as the PF175. I will contact for quotation if you still prefer the integer separation. muellenbroich
 (posted 2014-02-03 14:46:39.563) I also need to cut out a section in the centre of the board and additionally need two holes to allow periscopes to get through. Can you help making custom sized holes in standard sized breadboards? msoulby
 (posted 2014-02-04 07:16:52.0) Response from Mike at Thorlabs: We will contact you directly to discuss you custom breadboard requirements. ian.hill
 (posted 2013-06-25 14:08:24.45) If I were to cutout sections of the board would the honeycomb structure remain sufficiently intact to form a suitable edge and not fatally compromise the board? jlow
 (posted 2013-06-26 08:40:00.0) Response from Jeremy at Thorlabs: This depends on how the cut is made and the shape/location of the cut. Modifications like this are best done during production instead of post-production. We will get in contact with your to discuss about your application. jjurado
 (posted 2011-07-18 13:59:00.0) Response from Javier at Thorlabs to coopb: You can certainly drill additional holes as needed into the bottom of the breadboard. However, care must be exercised so as not to damage the internal honeycomb structure. coopb
 (posted 2011-07-15 08:37:01.0) Can I drill and tap additional mounting holes into the bottom of the board? Im using vibration isolating feet and need more than four to carry the load Im putting on the board.
Thanks,
Brian Adam
 (posted 2010-04-09 12:11:58.0) A response from Adam at Thorlabs to Karl: I will contact you direct to find out how far off the hole locations are on your board. The holes drilled on the top of the breadboard have a tolerance of +/- .004". The holes on the bottom of the breadboard are drilled by hand and have a larger tolerance, +/-.04". karl.vandyk
 (posted 2010-04-08 17:41:36.0) I just received the order TS0551689. I am trying to install the plates and I have found that the holes on the underside are not very accurate to the edge reference. I have two of these plates mounted side by side and the 1/4-20 holes on the top do not line up from one breadboard to the other. What is your tolerance on teh location holes on the underside?
Thanks
Karl van Dyk
Engineer
SRI international |
Breadboards | Nexus, Optimized Damping | Intrinsically Damped | Aluminum Honeycomb | Stainless Steel | Solid Aluminum |
---|---|---|---|---|---|
Construction | |||||
Breadboard Thickness | 60 mm (2.4") 110 mm (4.3") | 58 mm (2.28") | 25 mm (0.98") 55 mm (2.2") | 12.7 mm (0.5") | 7.0 mm (0.28") 9.5 mm (0.375") 12.7 mm (0.5") 19.05 mm (0.75") |
Working Surface | 4003 Grade Stainless Steel or 304L Grade Nonmagnetic Steel Top Plate | 4003 Grade Stainless Steel Top Plate | Aluminum | 416 Grade Stainless Steel | Solid Aluminum Anodized or Unanodized |
Top Skin | 5 mm (0.20") | 5 mm (0.20") | 6 mm (0.24") | N/A | N/A |
Bottom Skin | 5 mm (0.20") | 3 mm (0.12") | 3 mm (0.12") | N/A | N/A |
Core Design | High-Density Plated Steel Honeycomb, 0.26 mm Thick | High-Density Plated Aluminum Honeycomb | N/A | N/A | |
Side Panels | Rigid Steel Box Section | Unplasticized Polyvinyl Chloride (uPVC) | Black Laminated Aluminum Sides | N/A | N/A |
Ferromagnetism | Magnetic or Non-Magnetic Options | Magnetic | Non-Magnetic | Magnetic | Non-Magnetic |
Sealed Holes | Sealed (25 mm Depth) or Non-Sealed Options | Non-Sealed | N/A | N/A | |
Thread Options | 1/4"-20 (M6) Tapped Holes | 1/4"-20 (M6) Tapped Holes | 1/4"-20 (M6) Tapped Holes | 1/4"-20 (M6), 4-40 (M3), or 8-32 (M3) and 1/4"-20 (M6) Tapped Holes | |
Spacing | 1" (25 mm) Centers | 1" (25 mm) Centers | 1" (25 mm) Centers | 1" (25 mm) Centers or 0.5" (12.7 mm) Centers | |
Distance from Edge to First Holes | 0.5" (12.5 mm) on all Sides | 0.5" (12.5 mm) or 1.0" (25 mm) on all Sides | 0.5" (12.5 mm) on all Sides | 0.5" (12.5 mm) on all Sides | |
Performancea | |||||
Damping | N/A | N/A | |||
Stiffness | 60 mm (2.4") Thick | 58 mm (2.28") Thick | 25 mm (0.98") Thick | 12.7 mm (0.5") Thick | 7.0 mm (0.28") Thick |
110 mm (4.3") Thick | 55 mm (2.2") Thick | 19.05 mm (0.75") Thick |
光学ブレッドボードセレクションガイド
下記のセレクションガイドでは、当社のハニカム型およびソリッドタイプのアルミニウム製のブレッドボードをサイズごとにリストアップしています。まず、お探しのブレッドボードの幅と長さを見つけ、次にタイプをお選びください。それぞれの表は、ヘッダにあるMore [+] をクリックすると広がります。
当社では様々な種類のブレッドボードをご提供しております。冷却が必要な用途向けには、アルミニウム製の水冷式ブレッドボードをいくつかご用意しております。また、温度制御機能付きミニシリーズブレッドボードは規模の小さい用途向けです。手動制御のステージとして、アルマイト加工アルミニウム製の大型移動ステージや回転ブレッドボードをご用意しています。また、顕微鏡用途に適した製品として、手動式または電動式可動型取付けプラットフォームもございます。
Metric Optical Breadboard Size Options | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Width | Length | Honeycomb | Stainless Steel | Solid Aluminuma | ||||||
Nexus (60 mm Thick)b | Nexus (110 mm Thick)b | Intrinsically Damped (58 mm Thick) | Aluminum (25 mm Thick) | Aluminum (55 mm Thick) | Standard | Double Density | High Density |
Imperial Optical Breadboard Size Options | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Width | Length | Honeycomb | Stainless Steel | Solid Aluminuma | ||||||
Nexus (60 mm Thick)b | Nexus (110 mm Thick)b | Intrinsically Damped (58 mm Thick) | Aluminum (25 mm Thick) | Aluminum (55 mm Thick) | Standard | Double Density | High Density |
こちらのブレッドボードの側面には当社の25 mmレールおよびアクセサリが取り付け可能なTスロットが付いています。詳細は下の図をご覧ください。
Item # | Size | Number of Taps | Unpackaged Mass | Unpackaged Weight | Packaged Shipping Massa | Packaged Shipping Weighta | Distance From Edge to First Holes |
---|---|---|---|---|---|---|---|
PBG1212F | 12" x 12" | 144 | 2.9 kg | 6.4 lbs | 7.0 kg | 15.4 lbs | 0.5" |
PBG1218F | 12" x 18" | 216 | 4.1 kg | 9.0 lbs | 9.0 kg | 19.8 lbs | |
PBG1224F | 12" x 24" | 288 | 5.5 kg | 12.1 lbs | 11.0 kg | 24.3 lbs | |
PBG1236F | 12" x 36" | 432 | 8.1 kg | 17.9 lbs | 17.0 kg | 37.5 lbs | |
PBG1818F | 18" x 18" | 324 | 6.0 kg | 13.2 lbs | 12.0 kg | 26.5 lbs | |
PBG1824F | 18" x 24" | 432 | 8.1 kg | 17.9 lbs | 15.0 kg | 33.1 lbs | |
PBG2424F | 24" x 24" | 576 | 10.7 kg | 23.6 lbs | 18.0 kg | 39.7 lbs | |
PBG2436F | 24" x 36" | 864 | 15.8 kg | 34.8 lbs | 28.0 kg | 61.7 lbs | |
PBG2448F | 24" x 48" | 1152 | 20.9 kg | 46.1 lbs | 36.0 kg | 79.4 lbs | |
PBG3036F | 30" x 36" | 1080 | 19.6 kg | 43.2 lbs | 34.0 kg | 75.0 lbs | |
PBG3048F | 30" x 48" | 1440 | 26.0 kg | 57.3 lbs | 45.0 kg | 99.2 lbs | |
PBG3648F | 36" x 48" | 1728 | 31.0 kg | 68.3 lbs | 52.0 kg | 114.6 lbs |
こちらのブレッドボードの側面には当社の25 mmレールおよびアクセサリが取り付け可能なTスロットが付いています。詳細は左下の図をご覧ください。
Item # | Size | Number of Taps | Unpackaged Mass | Unpackaged Weight | Packaged Shipping Massa | Packaged Shipping Weighta | Distance From Edge to First Holes |
---|---|---|---|---|---|---|---|
PBG3030A | 300 mm x 300 mm | 144 | 2.8 kg | 6.2 lbs | 6.0 kg | 13.2 lbs | 12.5 mm |
PBG3045A | 300 mm x 450 mm | 216 | 4.1 kg | 9.0 lbs | 9.0 kg | 19.8 lbs | |
PBG3060A | 300 mm x 600 mm | 288 | 5.4 kg | 11.9 lbs | 11.0 kg | 24.3 lbs | |
PBG3090A | 300 mm x 900 mm | 432 | 8.0 kg | 17.6 lbs | 16.0 kg | 35.3 lbs | |
PBG4545A | 450 mm x 450 mm | 324 | 6.0 kg | 13.2 lbs | 11.0 kg | 24.3 lbs | |
PBG4560A | 450 mm x 600 mm | 432 | 7.9 kg | 17.4 lbs | 14.0 kg | 30.9 lbs | |
PBG6060A | 600 mm x 600 mm | 576 | 10.2 kg | 22.5 lbs | 18.0 kg | 39.7 lbs | |
PBG6090A | 600 mm x 900 mm | 864 | 15.3 kg | 33.7 lbs | 27.0 kg | 59.5 lbs | |
PBG60120A | 600 mm x 1200 mm | 1152 | 20.3 kg | 44.8 lbs | 35.0 kg | 77.2 lbs | |
PBG7590A | 750 mm x 900 mm | 1080 | 19.0 kg | 41.9 lbs | 33.0 kg | 72.8 lbs | |
PBG75120A | 750 mm x 1200 mm | 1440 | 25.2 kg | 55.6 lbs | 44.0 kg | 97.0 lbs | |
PBG90120A | 900 mm x 1200 mm | 1728 | 30.1 kg | 66.4 lbs | 50.0 kg | 110.2 lbs |