ファイバー出力レーザー光源:近赤外域(NIR)用
- SM and PM Sources Available
- Minimum Full Output Powers from 1.5 to 25.0 mW
- Stable, Low Noise, Constant Power Operation
S1FC808
808 nm, 25.0 mW
Front Panel Display Provides an Enable Button, Laser Power Control, and Display Screen
Please Wait
Single Channel Benchtop Laser Sources Selection Guide | |||||
---|---|---|---|---|---|
Spectrum | Wavelength | TEC | Laser Type | Cavity Type | Output Fiber Type |
Visible | 405 - 675 nm | No | Semiconductor | Fabry Perot | SM, MM, or PM |
405 - 685 nm | Yes | Semiconductor | Fabry Perot | SM | |
NIR | 785 - 1550 nm | No | Semiconductor | Fabry Perot | SM or PM |
705 - 2000 nm | Yes | Semiconductor | Fabry Perot | SM | |
1310 - 1550 nm | Yes | Semiconductor | DFB | SM | |
1900 - 2000 nm | N/A | Fiber Laser | Fabry Perot | SM | |
MIR | 2.7 µm | N/A | Fiber Laser | Fabry Perot | SM |
Other Fiber-Coupled Laser Sources |
特長
- シングルモードファイバまたは偏波保持ファイバ出力(波長:785~1550 nm)
- FC/PCのシングルモードまたはマルチモードファイバーインターフェイス
- 安定で低ノイズな一定出力動作
- 出力レベルはノブの回転またはBNC変調入力端子への入力電圧で調整可能
- インターロック回路は2.5 mmモノラルジャックに接続
当社では、近赤外域のスペクトルで発光するシングルモードファイバおよび偏波保持ファイバ出力のレーザ光源をご用意しています。このベンチトップ型のレーザ光源には、いずれもピグテール付きファブリペロー型半導体レーザと電流コントローラが内蔵されています。
レーザ光源の前面パネルには、出力値(mW)を表示するデイスプレイ、ON/OFFキー、Enableボタン、そしてレーザ出力調整ノブがあります。背面パネルには、外部からのDCまたは正弦波電圧信号によって半導体レーザの駆動電流を制御するためのBNC入力端子と、インターロック用リモートコントロール入力端子が付いています。
当社のシングルチャンネルベンチトップ型レーザ光源の全てのラインナップは右の表をご参照ください。
Single Mode Source Specifications | ||||||||
---|---|---|---|---|---|---|---|---|
Item # | S1FC780 | S1FC785 | S1FC808 | S1FC980 | S1FC1060 | S1FC1550 | ||
Wavelength | Minimum | 775 nm | 775 nm | 798 nm | 970 nm | 1054 nm | 1530 nm | |
Typical | 785 nm | 785 nm | 808 nm | 980 nm | 1064 nm | 1550 nm | ||
Maximum | 795 nm | 795 nm | 818 nm | 990 nm | 1074 nm | 1570 nm | ||
Spectruma | ||||||||
Minimum Full Output Power | 10.0 mW | 20.0 mW | 25.0 mW | 13.0 mW | 20.0 mW | 1.5 mW | ||
Setpoint Resolution | 0.01 mW | 0.1 mW | 0.1 mW | 0.01 mW | 0.1 mW | 0.01 mW | ||
Laser Class | 3B | 3B | 3B | 3B | 3B | 1 | ||
Fiber | ||||||||
Fiber Type | 780HP | 780HP | SM800-5.6-125 | SM980-5.8-125 | HI1060-J9 | SMF-28-J9 | ||
Mode Field Diameterb | 4.7 - 6.9 µm @ 830 nm | 5.0 ± 0.5 µm @ 850 nm | 4.7 - 6.9 µm @ 830 nm | 5.3 - 6.4 µm @ 980 nm | 6.2 ± 0.3 µm @ 1060 nm | 10.4 ± 0.5 µm @ 1550 nm | ||
Numerical Aperture | 0.10 - 0.14 | 0.13 | 0.10 - 0.14 | 0.13 - 0.15 | 0.14 | 0.14 | ||
Output Fiber Connector | FC/PC, Wide 2.1 mm Key Compatible | |||||||
Fiber | ||||||||
Power Stability | 15 min: ±0.05 dB, 24 hr: ±0.1 dB (After 1 hr Warm-up at 25 ± 10 °C Ambient) | |||||||
Display Accuracy | ±10% | |||||||
Adjustment Range | ~0 mW to Full Power | |||||||
Input Power | 115 VAC / 230 VAC (Switch Selectable) 50 - 60 Hz | |||||||
Modulation Input | 0 - 5 V = 0 - Full Power, DC or Sine Wave Input Only | |||||||
Modulation Bandwidth | 5 kHz Full Depth of Modulation 30 kHz Small Signal Modulation | |||||||
Environmental | ||||||||
Operating Temperature | 15 to 35 °C | |||||||
Storage Temperature | 0 to 50 °C |
Polarization-Maintaining Source Specifications | ||||
---|---|---|---|---|
Item # | S1FC780PM | S1FC1310PM | S1FC1550PM | |
Wavelengtha | 785 nm | 1310 nm | 1550 nm | |
Minimum Full Output Power | 6.25 mW | 1.5 mW | 1.5 mW | |
Extinction Ratioa | > 20 dB | > 23 dB | > 23 dB | |
Stability | 15 min: ±0.05 dB, 24 hr:±0.1 dB (After 1 hr Warm-up at 25 ± 10 °C Ambient) | |||
Display Accuracy | ±10% | |||
Setpoint Resolution | 0.01 mW | |||
Laser Class | 3B | 1 | ||
AdjustmentRange | ~0 mW to Full Power | |||
Environmental | ||||
Operating Temperature | 15 to 35 °C | |||
Storage Temperature | 0 to 50 °C | |||
AC Input | 115 VAC / 230 VAC (Switch Selectable) 50 - 60 Hz | |||
Modulation Input | 0 - 5 V = 0 - Full Power, DC or Sine Wave Input Only | |||
Modulation Bandwidth | 5 kHz Full Depth of Modulation 30 kHz Small Signal Modulation | |||
Fiber | PM780-HP | PM1300-HP | PM1550-HP |
変調入力端子
BNC メス型
0~5 Vまで、50 Ω
リモートインターロック入力端子
2.5 mmモノラルジャック
レーザの「ON」を有効にするためには、端子間を付属のプラグまたは外部スイッチのようなデバイスで短絡する必要があります。
Posted Comments: | |
Rawan Semaan
 (posted 2023-02-22 22:43:54.09) Hello,
I am interested in the Fiber-Coupled Laser Sources: NIR with 980 nm wavelength.
it stated that the Minimum Full Output Power is 13.0 mW. What is the maximum power?
Does this laser have internal modulation or do we need to modulate it externally?
Best regards,
Rawan ksosnowski
 (posted 2023-03-08 01:51:51.0) Hello Rawan, thanks for reaching out to Thorlabs. For S1FC980, we guarantee at least a full output power of 13.0mW or more, typically the max full output can be a little higher than this, though it varies slightly between units. The unit can be tuned from 0mW to max output. The power can be adjusted from 0mW to the full output power, using either the control knob or the analog modulation port. This laser does not have an internal frequency generator, but you can apply external DC or sine signals up to 5kHz to modulate the output. I've reached out directly to discuss this application further. Ben Garber
 (posted 2020-06-26 19:35:43.303) I was wondering what constitutes small-signal for the modulation bandwidth of the S1FC980. Specifically, for sine wave modulation, what kind of depth could we expect at 15kHz? asundararaj
 (posted 2020-07-07 04:41:55.0) Thank you for contacting Thorlabs. The small signal modulation amplitude is about 100 mV at 30 kHz, which is about a 2% modulation depth. I have contacted you directly about the performance at 15 kHz. |
- 6波長をご用意:785~1550 nm
- 最大出力: 1.5 mW~25.0 mW
- ファイバーパッチケーブルは別売りでご用意
こちらのファイバ出力レーザ光源は、ピグテール付きファブリペロー型半導体レーザと電流コントローラを1つのベンチトップ型ユニットに納めた製品です。各ユニット内のファブリペローレーザにはシングルモードファイバが接続されており、それらは前面パネルに取り付けられたFC/PCバルクヘッド(ワイドキー、ナローキーに対応)に接続されています。当社では前面パネルのバルクヘッドに接続するためのシングルモードファイバーパッチケーブルをご用意しております。接続損失を抑えるためにはレーザ装置内部で使用されているファイバと同じ種類のファイバーパッチケーブルを使用することをお勧めいたします。内部で使用されているファイバについては「仕様」タブをご覧ください。後方反射によるノイズを低減するために、レーザ光源に接続されたFC/PCコネクタに対して、ハイブリッド型のFC/PC-FC/APCケーブルのご使用をお勧めいたします。
前面パネルには、出力値(mW)を表示するデイスプレイ、ON/OFFキー、Enableボタン、そしてレーザ出力調整ノブがあります。背面パネルには、外部からのDCまたは正弦波電圧信号によって半導体レーザの駆動電流を制御するための入力端子と、インターロック用リモートコントロール入力端子が付いています。
注:この光源に他のファイバを接続、もしくは取り外す際には、レーザ出力をOFFにしてください。パワーレベルが10 mW以上の場合には特にご注意ください。
- 3波長をご用意:785 nm、1310 nm、1550 nm
- 最大出力:1.5 mW~6.25 mW
- ファイバーパッチケーブルは別売りでご用意
- 偏波保持ファイバのスロー軸がFC/PCバルクヘッドコネクタのナローキーにアライメント
こちらの偏波保持ファイバ出力型レーザ光源にはピグテール付きのファブリペローレーザがベンチトップ型ユニットに納められています。半導体レーザにはシングルモード偏波保持ファイバが結合されており、ユニット前面パネルに設置されたFC/PCバルクヘッドから出力されます。半導体レーザの偏光軸が偏波保持ファイバのスロー軸と合致するようファイバーアライメントが維持されています。また、偏波保持ファイバのスロー軸はベンチトップ型ユニット前面パネルのFC/PCバルクヘッドコネクタのナローキーにも合うように設計されています。当社では前面パネルのバルクヘッドに接続するための偏波保持ファイバーパッチケーブルをご用意しております。接続損失を抑えるためにはレーザ装置内部で使用されているファイバと同じ種類のファイバーパッチケーブルを使用することをお勧めいたします。内部で使用されているファイバについては「仕様」タブをご覧ください。後方反射によるノイズを低減するために、レーザ光源に接続されたFC/PCコネクタに対して、ハイブリッド型のFC/PC-FC/APCケーブルのご使用をお勧めいたします。
前面パネルには、出力値(mW)が表示できるディスプレイ、ON/OFF キー、Enableボタン、そしてレーザ出力調整ノブがあります。背面パネルには、外部からの電圧信号によって半導体レーザの駆動電流をコントロールするための入力端子とインターロック用リモートコントロール入力端子が付いています。
注:こちらのレーザを他のファイバに接続、もしくは他のファイバから取り外す際には、レーザ出力をOFFにしてください。